Advantech PCA-6179 Spécifications télécharger pdf (Page 3)

SNMP-1000-B1 Startup Manual 3

parameters can only be set through the serial port due to

security reasons.

A setup software utility can be found in the utility CDROM

shipped with the SNMP-1000-B1. It helps you to set up a

number of the SNMP-1000 system managers with same

configuration. You can save current configuration to a file

and copy it to other modules.

Before you can configure your SNMP-1000-B1 module,

you need first install your SNMP-1000-B1 and power it up.

Connect it to a network through its LAN port, or connect

its serial port to your PC using a "null modem" cable with

reversed Tx & Rx signals at one end. This cable is avail-

able from Advantech. (Part number: 1700091801)

When all the cables are well-connected, you can power up

the SNMP-1000-B1. A green LED on the kernel module

indicates that 5V power is supplied to SNMP-1000-B1.

Then it starts a self-testing procedure. It takes around 5

seconds, then it is ready to work.

Configuring through the serial port

The configuration example below if for Windows Hyperter-

minal (Windows95/98/ME/NT/2000/XP).

1. Start Hyperterminal by clicking on "Accessories" pro-

gram group.

2. Enter a name and choose an icon for the connection.

3. In the "Connect using" box, select "Direct to COMx."

Here “x” is the number of COM ports you are using to con-

nect to the SNMP-1000-B1.

4. Set the serial port of your PC to “9600 bps,” “8 data

bits,” “No parity,” and “1 stop bit with no flow control.”

5. Press the "Enter" key on your PC, then the SNMP-

1000-B1 will prompt you to enter administrator user name

and password. The default administrator user name is

"advantech" and password is "admin."

Note: Access through Telnet or serial port is permitted

only with the "Admin User Name" and "Admin

User Password" set in Control Group.

After entering the password, you can access the configu-

ration menu of SNMP-1000-B1.

Communicating through Ethernet

To communicate with SNMP-1000-B1 through Ethernet,

you need a computer with Ethernet and a TCP/IP network

installed. You need to know the IP address of the SNMP-

1000-B1 before you can communicate with it through the

Ethernet. There are four ways to determine the IP

address:

• The default IP address is 172.20.x.x where x.x are the

last four digits of the Ethernet MAC address. The MAC

address is labeled on the kernel module. For example, if

the MAC address is 00 E0 d8 03 15 36 (hexadecimal),

the IP address is then 172.20.21.54.

• You can read the IP address in console mode under

"Agent Configuration".

• You can read the IP address through the LCM display if

your SNMP-1000-B1 is connected to the LCM display

module.

• You can find all SNMP-1000-B1s connected on the

same network by using the setup utility.

Configuration using Telnet

Configuration using Telnet is basically same as using

serial port connection. First, make sure your computer has

a TCP/IP network and a web browser installed. In the

address line type "Telnet xxx.xxx.xxx.xxx." Here

xxx.xxx.xxx.xxx is the IP address of the SNMP-1000-B1.

Then the SNMP-1000-B1 will prompt you to enter user

name and password.

Configuration using a Web Browser

Using a web browser is the easiest way to configure the

SNMP-1000-B1. Type in the URL "http://xxx.xxx.xxx.xxx."

Here xxx.xxx.xxx.xxx is the IP address of the SNMP-

1000-B1. Then the SNMP-1000-B1 will prompt you to

enter user name and password.

Remote access through a phone line

SNMP-1000-B1's command mode can be accessed

remotely through a phone line. The SNMP-1000 -B1 has

to be connected to a phone line through a modem. Your

PC has to be connected to a phone line through a modem

too.

You can use HyperTerminal of the Windows system or

other dialing software tools. Please refer to the user's

manual of your dialing program for the setting details.

FCC: This device complies with the requirements in part

15 of the FCC rule.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received,

including interference that may cause undesired opera-

tion.

CAUTION!! Danger of explosion if battery is incor-

rectly replaced. The battery doesn’t need to be

charged. Replace only with Advantech-speci-

fied batteries.

1 2 3 4

Commentaires sur ces manuels

Pas de commentaire

Advantech PCA-6179 Spécifications Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Non Advantech PCA-6179