PPC-154Pentium® 4 Processor-Based Panel PC with 15" Color TFT LCD DisplayUsers Manual
PPC-153 User’s Manual xChapter 4 Hardware Installation and Upgrade ...284.1 Jumpers and Connectors...
xi6.1 Introduction ... 466.2 Driver Installation ...
PPC-153 User’s Manual xii
CHAPTER1General InformationThis chapter gives background information on the PPC-154 panel PC.Sections include:• Introduction• Specifications•
PPC-154 User’s Manual 2Chapter 1 General Information1.1 IntroductionAdvantech PPC-154T is an Intel Pentium 4 processor–based Panel PC with 15” LCD d
3 Chapter 1 1.2 SpecificationsGeneral• Dimensions (W x H x D): 420 x 323 x 130.5 mm (16.54" x 12.72" x 5.12")• Weight: 7 kg(15.4 lb
PPC-154 User’s Manual 4• PCI bus expansion slot: Accepts one PCI bus card• Watchdog timer: 62-level, interval 1 ~ 62 seconds. Automatically gen-erat
5 Chapter 1 • PCI bus interface: Complies with PCI Local Bus Specification 2.1, and supports the 32-bit Cardbus (Card-32) and the 16-bit PC card (Ca
PPC-154 User’s Manual 6Environment• Temperature: 0 ~ 45° C (32 ~ 122° F) • Relative humidity: 10 ~ 95% @ 40° C (non-condensing)• Shock: 10 G peak
CHAPTER 2System SetupThis chapter details system setup on the PPC-154 panel PC.Sections include:• A Quick Tour of the Panel PC• Preparing for First-
PPC-154 User’s Manual iiCopyrightThis document is copyrighted, © 2004. All rights are reserved. The origi-nal manufacturer reserves the right to make
PPC-154 User’s Manual 12Chapter 2 System Setup2.1 A Quick Tour of the Panel PCBefore you start to set up the panel PC, take a moment to become famil
13 Chapter 2 When you look at the left side of the panel PC, you will see the floppy disk drive, CD-ROM drive and PCMCIA expansion sockets, as shown
PPC-154 User’s Manual 142.2 Preparing for First-time UseBefore you start to set up the panel PC system, you should have at least the following items
15 Chapter 2 2.4 Running the BIOS Setup ProgramYour panel PC is likely to have been properly set up and configured by your dealer prior to delivery.
PPC-154 User’s Manual 162.5 Installing System SoftwareRecent releases of operating systems from major vendors include setup programs which load autom
17 Chapter 2 2.6 Installing the DriversAfter installing your system software, you will be able to set up the Ether-net, SVGA, audio, PCMCIA and touc
PPC-154 User’s Manual 18
CHAPTER 3Using the Panel PCThis chapter details installing thePPC-154 panel PC hardware.Sections include:• Introduction• Floppy Drive• CD-ROM Drive
PPC-154 User’s Manual 20Chapter 3 Using the Panel PC3.1 IntroductionThis chapter describes basic features and procedures for using the panel PC. Top
21 Chapter 3 3.3 CD-ROM DriveTo insert a CD-ROM disc, press the eject button of the CD-ROM drive. The yellow activity light will flash and the front
iiiFCC Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. T
PPC-154 User’s Manual 223.4 Multi-card ReaderMemory Flash Cards are inserted and ejected in much the same way as diskettes.To insert a Flash Memory
23 Chapter 3 3.5 PS/2 Mouse and KeyboardIf you wish to use a full-size desktop keyboard and PS/2 mouse with your panel PC, follow these instructions
PPC-154 User’s Manual 243.7 Parallel portThe panel PC supports the latest EPP and ECP parallel port protocols for improved performance and versatilit
25 Chapter 3 3.9 VGA PortAn external VGA-compatible device may be connected to the system through the 15-pin external port located on the rear of th
PPC-154 User’s Manual 263.12 Audio InterfaceThe audio interface includes three jacks: microphone in, line out and line in. (See Fig. 3-5.) Their func
CHAPTER 4Hardware Installation and UpgradeThis chapter tells how to set up the panel PC hardware, including instruc-tions on setting jumpers and conne
PPC-154 User’s Manual 28Chapter 4 Hardware Installation and Upgrade4.1 Jumpers and ConnectorsThe panel PC consists of a PC-based computer that is ho
29 Chapter 4 4.2 Disassembling the Panel PCThe following are standard procedures for disassembling the panel PC before you upgrade your system. All
PPC-154 User’s Manual 303. Lift the right side of the rear cover first to remove it.Figure 4.3: Opening the rear coverFigure 4.4: The PPC without the
31 Chapter 4 4.3 Installing the 2.5" Hard Disk Drive (HDD)You can attach one enhanced Integrated Device Electronics (IDE) hard disk drive to th
PPC-154 User’s Manual ivPacking List Before you begin installing your car
PPC-154 User’s Manual 32Figure 4.7: Plug the EIDE cable into the HDD Figure 4.8: Screw the right side of the metal plate to fix itFigure 4.9: Screw th
33 Chapter 4 1. Detach and remove the plastic rear cover and side panel.2. There is a metal plate which holds the HDD to the upper right-hand side of
PPC-154 User’s Manual 341. Lift up the ZIF.2. Place the CPU carefully into the socket. 3. Attach the heatsink and fan on top of the CPU, and fasten th
35 Chapter 4 4. Detach.the CPU’s fan power cable to the connector FAN14.5 Installing the DDR SDRAM Memory ModuleYou can install from 64 MB to 2 GB o
PPC-154 User’s Manual 36
CHAPTER 5Jumper Settings and ConnectorsThis chapter tells how to set up the panel PC hardware, including instruc-tions on setting jumpers and connecti
PPC-154 User’s Manual 38Chapter 5 Jumper Settings & Connectors5.1 Jumpers and Connectors5.1.1 Setting jumpersYou can configure your panel PC to
39 Chapter 5 5.1.2 Jumpers and switchesThe motherboard of the PPC-153 has a number of jumpers that allow you to configure your system to suit your ap
PPC-154 User’s Manual 405.1.4 ConnectorsOnboard connectors link the panel PC to external devices such as hard disk drives or floppy drives. The table
41 Chapter 5 5.1.5 Locating connectorsFigure 5.2: Connectors on PPC-153 motherboard
vAdditional Information and Assistance Step 1. Visit the Advantech web site at www.advantech.com where you can find t
PPC-154 User’s Manual 425.2 CPU InstallationYou can install an Intel® Pentium®4 or Celeron™ CPU without setting any frequency ratio or voltage.*Defau
43 Chapter 5 5.4 COM-port interface (JP4, JP5)The panel PC provides two serial ports. COM1 (RS-232) and COM2 (RS-232/422/485) in one COM port connec
PPC-154 User’s Manual 445.5 VGA interfaceThe panel PC's AGP VGA interface can drive conventional CRT dis-plays. It is also capable of driving a
CHAPTER 6Driver InstallationThis chapter provides information on how to install the drivers for PPC-154Sections include:• Introduction• Installation
PPC-154 User’s Manual 46Chapter 6 Driver Installation6.1 IntroductionThe PPC-154 uses the chipset 845GV from Intel., with built-in high per-formance
47 Chapter 6 6.2.1 Installation of VGA driverPlease follow the driver path and execute it .D:\PPC-154\VGA\winxxxx\setup.exe.6.2.2 Installation of Aud
PPC-154 User’s Manual 486.2.9 Further InformationFor further information about the AGP/VGA installation in your PPC-153, including driver updates, tro
AppendixAPin Assignments
PPC-154 User’s Manual 50Appendix A Pin AssignmentsA.1 ATX Power connector 1 (CN1) Table A.1: AT Power connector 1 (CN1)Pin Signal Pin Signal1 3.3V
51 Appendix A A.2 ATX power connector 2 (CN2)A.3 LVDS connector 1(CN4)Table A.2: ATX power connector 2 (CN2)Pin Signal Pin Signal1GND312V2GND412VTa
PPC-154 User’s Manual viSafety Instructions 1. Read these sa
PPC-154 User’s Manual 52A.4 LVDS connector 2(CN6)A.5 Inverter power connector (CN5)Table A.4: Table B.4: LVDS connector 2 (CN6)Pin Signal Pin Signal
53 Appendix A A.6 FDD connector (CN9)Table A.6: FDD connector (CN9)Pin Signal Pin Signal1 Vcc(+5V) 14 Step2 Index 15 GND3 Vcc(+5V) 16 Write data4 Dr
PPC-154 User’s Manual 54A.7 Internal speaker connector (CN15)A.8 IR connector (CN24)A.9 Fan power connector (FAN1 & FAN2)Table A.7: Internal sp
AppendixBFull Disassembly Procedure
PPC-154 User’s Manual 56Appendix B Full Disassembly ProcedureIf you want to completely disassemble the panel PC, follow the step-by-step procedures b
57 Appendix B 3. Lift the right side of the rear cover first to remove it4. The PPC without the rear cover5. Unscrew the board of the card reader
PPC-154 User’s Manual 586. Unscrew the screw of PCI extension bus card away from PCI slot 7. Lift out the metal plate of the I/O shield from the I/O8
59 Appendix B 9. Lift out the cable from the CD-ROM10. Unscrew the two screws of the bottom side to loosen the metal plate of CD-ROM / FDD module1
PPC-154 User’s Manual 6012. Unscrew the screws to loosen the CD-ROM and FDD from mod-ule.13. Lift the FDD from the module.14. Unscrew the screws
61 Appendix B 15. Lift up the ATX 20 pins power connector.16. Lift up the ATX 12V 4 pins power connector.17. Lift up the EIDE cable from mainboard.
viiWi ch t ig e S ich er h ei s h in we i se 1. Bitte lesen sie Sich die
PPC-154 User’s Manual 6218. Loosen the screws from the bottom for remove the power module19. Loosen the screws to lift up the board
PPC-154 User’s Manual viii
ix|ContentsChapter 1 General Information ...........21.1 Introduction ..............
Commentaires sur ces manuels