Advantech ACP-4320 Manuel d'utilisateur

ACP-43204U Height Industrial Chassis with Dual front accessible SAS/SATA HDD Trays for Easy MaintenanceUser Manual

ACP-4320 User Manual viiiChapter 3 Operation ...223.1 The Front Section of ACP-4320...

1CHAPTER1General Information

ACP-4320 User Manual 2Chapter 1 General Information1.1 IntroductionThe ACP-4320 is a 4U-high rackmount industrial computer chassis designed for buil

31.2 SpecificationsGeneral• Construction: Heavy duty steel chassis• Disk drive capacity: Two front-accessible mobile trays for 3.5" SAS/SATA

ACP-4320 User Manual 41.4 Power Supply Options 1.4.1 300W ATX power supply with PFC (PS-300ATX-ZBE)• Output rating: 300 watts max.• Input rat

51.4.4 400W ATX redundant power supply (RPS-400ATX-ZE)• Output rating: 400 watts max.• Input rating: 100 ~ 240 VAC @ 47 ~ 63 Hz (full range)• O

ACP-4320 User Manual 61.5 Passive Backplane OptionsThe ACP-4320BP chassis accepts up to a 15-slot backplane. Here is a summary of the supported back

71.6 Dimensions of ACP-4320Figure 1.1: Dimensions of ACP-4320 Unit: mm (inch)

ACP-4320 User Manual 81.7 Ordering InformationTable 1.3: ACP-4320 model listPart Number Power SupplyMotherboard/BackplaneRegulationMB VersionACP-4320

9CHAPTER2System Setup

ACP-4320 User Manual iiCopyrightThis document is copyrighted, 2008, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the r

ACP-4320 User Manual 10Chapter 2 System SetupThe following procedures are provided to assist you in installing a moth-erboard (or backplane), disk dr

112.2 Installing the Motherboard The ACP-4320MB accepts both an ATX and a microATX motherboard. To install a motherboard, please proc

ACP-4320 User Manual 125. Refer to Figure 2.2, place the motherboard into the chassis, and fix it with screws.6. Plug in the 20- or 24-pin ATX power

132.3 Installing the Backplane & CPU CardThe ACP-4320BP accepts an up to 15-slot PICMG 1.0 backplane or 12-slot PICMG 1.3 express backplane. To i

ACP-4320 User Manual 142.3.2 Installing the CPU Card1. Before installing the CPU card, check all devices, such as CPU, CPU cooler and RAM modules a

152.4 Installing Add-on CardTo install a plug-in card, please proceed as follows:1. Select a vacant slot to install the add-on card. Then remove the

ACP-4320 User Manual 162.5 Installing Disk DrivesThe ACP-4320 comes with two front-accessible SAS/SATA HDD trays; it also supports two 5.25" di

17.Figure 2.5: Installing the drives2.5.1 Installing a 5.25" disk drive1. Remove the two screws, which mount the FDD bracket to the drive bay

ACP-4320 User Manual 182.5.2 Installing a 3.5" floppy disk drive1. Remove the cover of one 3.5" drive bay.2. Insert one 3.5" floppy

192.5.4 Installing a SAS/SATA HDD in the front-accessible HDD trayACP-4320 accepts both SAS and SATA HDDs. It is not necessary to remove the top cover

iiiSafety Instructions1. Read these safety instructions carefully.2. Keep this installation reference guide for later reference.3. Disconnect th

21CHAPTER3Operation

ACP-4320 User Manual 22Chapter 3 Operation3.1 The Front Section of ACP-4320 3.1.1 Switch and buttonsFigure 3.1: The switch & buttons

233.1.2 LED indicators for System StatusFigure 3.2: The LEDs on the front panelSix LEDs (shown as Figure 3.2) are placed on the front panel of the A

ACP-4320 User Manual 24When the FAN LED is RED and blinking, it indicates a failed cooling fan, and the alarm buzzer is also activated. To stop the a

253.2 Replacing the FansThere is one fan behind the front plate of ACP-4320 chassis and one fan behind the SAS/SATA drive bay. To replace either of t

ACP-4320 User Manual 267. Slide the fan bracket back to the chassis and fasten the thumb screw. 8. Plug in the fan power connector.3.2.2 Replacing

273.3 Cleaning the Filters There are two filters in the ACP-4320: one in front of the fan and the other behind the front door. To

ACP-4320 User Manual 283.4 Replacing the Power Supply The ACP-4320 supports either 300W/400W single PS/2 or 300W/400W redundant power supplies. To

297. Plug the ATX power connector and +12V power connector to the backplane/motherboard, as well as the hard disk drive and floppy drive and the peri

ACP-4320 User Manual iv15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW 0°C (32°F) OR ABOVE 40°

31CHAPTER4Alarm Board

ACP-4320 User Manual 32Chapter 4 Alarm BoardThe alarm board is located under the system fan. It makes an audible alarm when:• Any power supply modul

334.2 Alarm board specifications Input Power: +5V, +12V Input Signals: • 7 fan connectors• One thermal sensor connector (connects up to 8 therm

ACP-4320 User Manual 34CN17: Alarm Reset connectorPin 1 Alarm reset Pin 2 GNDCN18: Output connector to LED BoardPin 1 GND Pin 2 +5 V SignalPin 3 +12

354.2.2 Switch settingsThe alarm board is designed to connect with up to 7 fans. User can set the fan number by adjusting the switch, SW1, on the alar

ACP-4320 User Manual 36Table 4.3: CN1 & CN2, Temperature sensor connectorPin 1 +5 V Pin 2 T_SCLKPin 3 T_SDAT Pin 4 GNDTable 4.4: SW1, Thermal

37 Appendix A AppendixAExploded Diagram

ACP-4320 User Manual 38Appendix A Exploded Diagram Figure A.1: Exploded diagram

vA Message to the Customer Advantech customer servicesEach and every Advantech product is built to the

Product warranty Advantech warrants to you, the original purchaser, that each of its prod-ucts will be free from defects in materials and workmanship

viiInitial Inspection Before you installing your backplane or motherboard, please make sure that the following materials have been shipped:• ACP-432

ACP-4320 User Manual viii

viiContentsChapter 1 General Information ...........21.1 Introduction ..............